Skip to content
AirModuleLink

Launching mid-December 2026 / From the creators of IgniteRemote

Program the car without driving to it.

AirModuleLink plugs into the OBD-II port and puts your own key programmer, scan tool or OEM software on a car that is somewhere else. Whoever is with the car plugs in one lead. You do the job from your bench.

  • Ships from mid-December 2026
  • Deposit refundable until it ships
  • Introductory price for the list
The AirModuleLink box, a graphite case with orange corner bumpers, with its OBD-II lead beside it

Product render

Proven on vehicles
The J2534 link
With FDRS, wiTECH, SDD and CONSULT-III plus.
Proven on the bench
Tool Tunnel over CAN
A tool on one bench reading a module on another.
Online in
About a minute
Cable, phone lead or Wi-Fi. Nothing to install.
Launch
Mid-December
First batch, built and bench-tested by hand.

The problem

A twenty-minute job should not cost you half a day.

The programming takes minutes. Getting you and the car into the same place is what eats the day, and there have only ever been three ways to pay for that.

AirModuleLink takes the distance out, so you can reach more customers without adding a single mile.

How it works

Three steps. Only one of them touches the car.

Nobody at the car needs to know anything about programming. If they can plug in a phone charger, they can do their part.
  1. The AirModuleLink box on the floor of a car with its lead plugged into the OBD-II port under the dashboard

    Step 1 / at the car

    Plug it in.

    Whoever is with the car pushes one lead into the OBD-II port under the dashboard. A customer can do it, or a porter, or the driver who delivered it. That lead is the only thing that connects to the car.

    The box runs from its own battery, so it draws nothing from the vehicle.

  2. The back of the AirModuleLink box with a network cable and a phone lead plugged in, and a phone showing the box's setup page

    Step 2 / at the car

    Get it online.

    Join the box's own Wi-Fi from a phone and share the internet with it, plug the phone straight into the box, or plug in a network cable. Whichever one is there, the box takes it by itself and is online in about a minute.

    The three ways, step by step

  3. The AirModuleLink box seen from the front with its OBD-II plug in the foreground

    Step 3 / at your bench

    You are on the car.

    Pick the box from the list in your console and press Start. Your key programmer at the dock, or the OEM software on your own computer, talks to that car as though it were in your bay.

    No addresses, ports or codes to read out over the phone.

For the person at the car

Three ways online. Use whichever is closest.

The box has no screen and needs no app. Its setup page opens on the phone in your customer's hand, and the box looks for a way out by itself.
  1. No cables

    AShare Wi-Fi from a phone

    1. 1On a phone, join the Wi-Fi named IgniteRemote and four characters. Its name and password come with the box.
    2. 2A page opens by itself. Pick the Wi-Fi the box should use, or enter the phone's own hotspot, and type that network's password.
    3. 3Press Connect this box. If you chose the phone's hotspot, switch it on now.

    The box raises this setup network by itself when nothing is plugged in, and remembers a network that worked.

    Proven on the bench
  2. Fewest steps

    BPlug a phone into it

    1. 1Plug the phone into the box's USB port with its normal data cable.
    2. 2Turn on USB tethering on Android. On an iPhone, tap Trust, then turn on Personal Hotspot.

    Nothing is typed anywhere, and the phone charges while it shares.

    Proven on the bench
  3. Steadiest link

    CPlug in a network cable

    1. 1Run a cable from a router or a wall socket to the box.

    A cable always wins over the other two. This is the one to use for a long session.

    Proven on the bench

Whichever one is there, the box takes it by itself and shows up in your technician's console within about a minute.

Two ways to work

Bring your own tool, or your own OEM software.

A remote programming service sells you its technician. This is the opposite: the equipment and the subscriptions you already paid for, reaching further.

Tool Tunnel

Proven on the bench

Your own key programmer or diagnostic tool stays at your shop, plugged into the dock, and behaves as though the car were on the bench in front of it.

  1. The car

    OBD-II port

  2. AirModuleLink

    at the car

  3. Dock

    at your shop

  4. Your tool

    key programmer or scan tool

  • The tunnel carries CAN frames without reading them, so the tool's own protocol passes through untouched.
  • The dock is a powered OBD-II socket. Your tool plugs into it exactly as it plugs into a car.

A standalone diagnostic tool read live fault codes from an engine control module bench to bench, through the tunnel (20 September 2026).

J2534 pass-thru

Proven on vehicles

The vehicle maker's own software runs on your computer and drives the car through the IgniteRemote J2534 link, so the subscription and its login stay with you.

  1. The car

    OBD-II port

  2. J2534 interface

    at the car

  3. J2534 link

    IgniteRemote

  4. OEM software

    on your computer

The J2534 link is used with

  • Ford FDRS / FJDS
  • Chrysler wiTECH
  • JLR SDD
  • Nissan CONSULT-III plus
  • GM Techline Connect
  • Toyota Techstream
  • Volvo VIDA
  • VW / Audi ODIS
  • BMW ISTA

The IgniteRemote J2534 link, with a pass-thru interface at the vehicle, has been used on real vehicles with Ford FDRS and FJDS, Chrysler wiTECH, JLR SDD and Nissan CONSULT-III plus, key programming included.

AirModuleLink is designed to be that interface at the car itself. How J2534 works at a distance

Protocols and pins

CAN, CAN FD and DoIP, pin by pin.

One lead brings all sixteen pins of the OBD-II connector to the box: CAN on 6 and 14, the second pair on 3 and 11, and DoIP Ethernet on 12, 13 and 8. Choose a pin to see what it carries.
12345678910111213141516Looking into the socket under the dash
  • Main CAN bus
  • Second CAN bus
  • DoIP Ethernet
  • Ground
  • Not used

Pin 6

CAN high

Main CAN bus

The main diagnostic bus (ISO 15765-4). Classic CAN and CAN FD.

Works as a pair with pin .

CAN FD, DoIP, J2534 and the OBD-II pinout explained

Safety

It will refuse a bad link before it risks a module.

The worst thing a remote link can do is drop in the middle of a write. So the first defence is not starting one over a connection that cannot finish it.

Proof

What we have proven, and how.

Not a list of features: the tests behind them. Here is what was run, on what, and when.

All 14 proofs, with dates

Exploded view of the AirModuleLink box: lid, electronics, battery bay and the four orange corner bumpers

Product render

Inside the box

A small computer in a case built to be thrown in a van.

Everything is in one enclosure with one lead. There is no laptop to charge, no dongle to pair and no screen to crack.
Computer
Raspberry Pi Compute Module 5
Vehicle side
Two CAN FD channels, on pins 6 and 14 and pins 3 and 11, and DoIP Ethernet
Getting online
Wi-Fi, a phone on USB, or Ethernet
Power
Internal battery and UPS board, charged over USB-C
Case
4 mm ASA shell with replaceable TPU corner bumpers
Size
192 x 150 x 107 mm over the bumpers
Built in
Arlington, Texas

Compare

The other ways to do this, and what they publish.

Most remote programming is a service: their technician, their tool, a fee for every module. A few are boxes. Here is how they line up on the questions that decide it.
AirModuleLink compared with other ways of programming a vehicle remotely, as published on 21 November 2026
QuestionAirModuleLinkOpus IVS RAP / RAP2Autel Remote Expert with MaxiFlash XLinkLaunch SmartLink C and SmartLink B
Who does the programmingYour technician with your own tools, or our benchTheir programmersAn expert from Autel's marketplaceWhoever holds the SmartLink B
Per jobAnnounced with the price$149 to $218 per module by make, plus $50 to $95 per calibration checkSet by the expert for each jobNot published
Your own key programmer or scan toolYes. A CAN key programmer or diagnostic tool at your shop, through the Tool Tunnel.No. The session is run on their kit by their team.No. Works within Autel's hardware and platform.Yes, per Launch: SmartLink B connects to a diagnostic device.
OEM softwareYours, on your own computer, through the IgniteRemote J2534 linkTheirs, on their sideThe expert'sSmartLink C is described as a J2534 reflashing device

Other products as their makers publish them, read on 21 November 2026. “Not published” means we found no public figure, not that there is none. Sources are on each comparison page.

The full comparison, with sources

Launching mid-December 2026

Three ways to get one.

Join the list to receive the introductory price, reserve a box from the first batch today for $99, or order outright once the price is published.

Join the list

Free

Get the introductory price first.

  • The introductory price by email, before it is public
  • First notice when ordering opens
  • No payment and no obligation
First batch

Reserve today

$99

Hold a box from the first batch.

  • A box from the first batch

    Reservations are filled in the order they arrive.

  • The introductory price

    You pay the introductory price when your box is ready, whatever the price is by then.

  • The deposit comes off the price

    It is a payment toward your box, not a fee on top of it.

  • Refundable until it ships

    Change your mind for any reason before your box ships and the whole deposit goes back.

Order now

Full price

Buy it outright, shipped mid-december.

  • Pay once and your box ships from mid-December 2026
  • Set up with you, on a call, with your tool on the other end

Ordering opens as soon as the price is published. People on the list and with a reservation hear first.

Why the first batch is small

Each case takes about a day to print, and every box is assembled and bench-tested by hand in Arlington, Texas. Reservations are filled in the order they arrive.

From the creators of IgniteRemote

Built by a locksmith, for his own customers first.

Adrian Torres started AirModuleLink to use with his own customers: a way to program their cars without sending a technician to each one. It comes from the team that makes IgniteRemote, the remote link shops use to flash modules.

The same box lets you expand your business and reach more customers remotely.

More about who makes it

  • A locksmith since 2012

    Keys, immobilizers and module programming on customers' cars.

  • Managed more than 15 technicians

    Across major metro areas, including Miami, Houston, San Antonio and Austin.

  • Builds the software his shops run on

    IgniteRemote, Run with Jarvis, The Key Bot, IntelliDrive and GetTimePad.

  • A degree in business administration

    He builds for shops because he runs them.

Questions

What shops ask first.

What is AirModuleLink?

AirModuleLink is a rugged box that plugs into a vehicle's OBD-II diagnostic port and connects that car to a technician somewhere else. The technician uses their own key programmer, diagnostic tool or OEM software as though the car were in front of them. The person at the car only plugs the box in and gets it online.

How is this different from a remote programming service?

A remote programming service sells you a job done by its own technicians on its own equipment. AirModuleLink is the link itself: your tools, your OEM subscriptions and your technician, on a car that is somewhere else. If you have no programmer, our own bench can be the technician on the other end.

What does the person at the car have to do?

Three things. Plug the lead into the OBD-II port. Get the box online, by plugging in a network cable, by plugging in a phone and turning on tethering, or by joining the box's own setup Wi-Fi and choosing a network. Then tell the technician it is in. There is no computer, no app to install and nothing to type on the box.

Which vehicles does it work on?

Vehicles with CAN at the OBD-II port, which is every car and light truck sold in the United States since model year 2008. It carries classic CAN and CAN FD on pins 6 and 14, the second CAN pair some makes put on pins 3 and 11, and DoIP diagnostics for cars that use Ethernet. Older vehicles that speak only K-line or J1850 are outside its range. What your tool can do on a given car is still decided by the tool.

What does it cost?

The price of the box will be announced before launch in mid-December 2026. Join the list and we will email you the introductory price first, or reserve a box from the first batch today for $99. The deposit comes off the price and is refundable until your box ships.

Can I get my deposit back?

Yes. Change your mind for any reason before your box ships and the whole deposit goes back.

All 23 questions

Launching mid-December 2026

Put your bench in a car that is somewhere else.

Reserve a box from the first batch today for $99, refundable until it ships. Or join the list and get the introductory price before it is public.